A practical reference on Primary drying: what it is, how it behaves, what the literature reports, and where the honest uncertainties sit.
Reviewed 2025-09-30. Anything still debated is marked as such rather than presented as settled.
The physics of freeze-drying couples heat transfer, mass transfer, and phase change. Heat supplied through the shelf must reach the sublimation front without melting the ice or degrading the product. Water vapor then travels through the already dried layer and leaves the chamber, where low pressure and cold traps keep it from returning. The dried layer acts as a resistance to vapor flow, so drying rate changes as the front recedes. Open questions remain about how pore structure and formulation heterogeneity affect drying uniformity at larger scales.
Lyophilization removes water from a frozen material by sublimation under reduced pressure. The process begins with freezing, which converts liquid water into ice and concentrates dissolved solids. Primary drying then lowers chamber pressure so ice changes directly into vapor without passing through a liquid phase. Secondary drying raises the shelf temperature to remove bound water that remains after ice sublimation. The result is a dry, porous structure that can be reconstituted later.
Formulation composition influences whether freeze-drying produces an intact cake or a collapsed mass. Excipients such as sugars and polymers can raise the collapse temperature and provide bulk during drying. The critical temperature for primary drying is often the collapse temperature or the glass transition temperature of the maximally concentrated phase. If the product temperature exceeds this threshold, the frozen matrix may soften and lose structure. Established practice therefore links shelf temperature and chamber pressure to the formulation's thermal properties.
Freeze-drying is distinct from simple evaporation and from spray drying. Evaporation removes water at temperatures above freezing, while spray drying rapidly dries droplets in a heated gas stream. Lyophilization avoids high temperatures, which can be useful for heat-sensitive materials such as proteins, vaccines, and some foods. The porous cake produced by sublimation dissolves or rehydrates more quickly than a dense dried mass. Not all materials tolerate freezing or the pH shifts that can occur as solutes concentrate during ice formation.
Lyophilization removes water from a frozen material by sublimation under reduced pressure. The process begins with freezing, which converts liquid water into ice and fixes the structure of the sample. After freezing, primary drying lowers pressure so ice changes directly to vapor without passing through a liquid phase. Secondary drying then removes bound water that remains after ice sublimation. The result is a dry, porous solid that often retains its original shape.
| Property | Value | Notes |
|---|---|---|
| Common name | Freeze-drying | Process removes water by sublimation under vacuum. |
| Typical primary drying shelf temperature | -40 C to -10 C | Set below the formulation's collapse temperature. |
| Typical chamber pressure | 0.05-0.3 mbar | Low pressure allows ice to sublime below its triple point. |
| Water content after drying | 0.5-3% by weight | Higher values may reduce storage stability for some materials. |
| Key thermal parameter | Collapse temperature | Measured by freeze-drying microscopy or differential scanning calorimetry. |
A typical cycle begins with freezing, sometimes including an annealing step to control ice crystal size. Freezing conditions influence the pore network that later allows vapor escape. During primary drying, shelf temperature and chamber pressure are set so heat enters the product while its temperature stays below the collapse or eutectic point. Secondary drying then raises the shelf temperature to desorb bound water and lower residual moisture. Cycle design depends on formulation, fill volume, container type, and equipment capability.
The physics of lyophilization couples heat transfer, mass transfer, and phase behavior. Sublimation requires a vapor pressure difference between the ice front and the chamber, and the dried layer adds resistance to vapor flow. Amorphous formulations are characterized by a glass transition temperature of the maximally freeze-concentrated solute, often denoted Tg'. Crystalline bulking agents can provide structure, while amorphous excipients stabilize labile components. Open questions remain about spatial heterogeneity, edge effects, and how laboratory cycles scale to production.
Lyophilization is a drying process in which a solvent, usually water, is removed from a frozen material by sublimation under reduced pressure. The material is first solidified, then placed under vacuum so that ice transitions directly to vapor without a bulk liquid phase. This approach suits heat-sensitive substances that would degrade during conventional evaporation. Primary drying removes unbound ice, while secondary drying reduces water that remains adsorbed to the solid matrix. The result is a porous, lightweight solid that can be reconstituted later.
Lyophilization is a dehydration process that removes water from a frozen material by sublimation under low pressure. The material is first frozen to convert liquid water into ice. Next, the pressure is reduced below the triple point of water so that ice changes directly into vapor without passing through a liquid phase. This step is called primary drying. The result is a porous solid or cake that retains the original shape of the frozen solution.
After primary drying, secondary drying removes water that remains bound to the material. This stage raises the shelf temperature while maintaining low pressure, which encourages desorption of unfrozen water. Residual moisture can be reduced to a low percentage, improving stability for many products. The process parameters, including freezing rate, shelf temperature, and chamber pressure, influence the final pore structure and reconstitution behavior. Control of these variables helps prevent collapse or meltback during drying.
In the phosphatidylinositol signal pathway, the extracellular signal molecule binds with the G-protein receptor (Gq) on the cell surface and activates phospholipase C, which is located on the plasma membrane. The lipase hydrolyzes PIP2 into two second messengers: inositol 1,4,5-trisphosphate (IP3) and diacylglycerol (DAG). IP3 binds with the IP3 receptor in the membrane of the smooth endoplasmic reticulum and mitochondria to open Ca2+ channels. DAG helps activate protein kinase C (PKC), which phosphorylates many other proteins, changing their catalytic activities, leading to cellular responses. The effects of Ca2+ are also remarkable: it cooperates with DAG in activating PKC and can activate the CaM kinase pathway, in which calcium-modulated protein calmodulin (CaM) binds Ca2+, undergoes a change in conformation, and activates CaM kinase II, which has unique ability to increase its binding affinity to CaM by autophosphorylation, making CaM unavailable for the activation of other enzymes. The kinase then phosphorylates target enzymes, regulating their activities. The two signal pathways are connected together by Ca2+-CaM, which is also a regulatory subunit of adenylyl cyclase and phosphodiesterase in the cAMP signal pathway.
In addition to regulating the experiments that were conducted, the guidelines also forbade the performance of other experiments. One such experiment was the cloning of recombinant DNAs derived from highly pathogenic organisms. In addition, neither the cloning of DNA containing toxin genes nor large-scale experiments using recombinant DNAs that were able to make products that were potentially harmful to humans, animals, or plants were allowed under the guidelines. These experiments were banned because the potential biohazards could not be contained by the then-current safety precautions.
14-3-3 proteins play an isoform-specific role in class switch recombination. They are believed to interact with the protein activation-induced cytidine deaminase in mediating class switch recombination. Phosphorylation of Cdc25C by CDS1 and CHEK1 creates a binding site for the 14-3-3 family of phosphoserine binding proteins. Binding of 14-3-3 has little effect on Cdc25C activity, and it is believed that 14-3-3 regulates Cdc25C by sequestering it to the cytoplasm, thereby preventing the interactions with CycB-Cdk1 that are localized to the nucleus at the G2/M transition. The eta isoform, YWHAH, is reported to be a biomarker (in synovial fluid) for rheumatoid arthritis. In a systematic review, 14-3-3η has been described as a welcome addition to the rheumatology field. The authors indicate that the serum based 14-3-3η marker is additive to the armamentarium of existing tools available to clinicians, and that there is adequate clinical evidence to support its clinical benefits in the management of patients diagnosed with rheumatoid arthritis (RA). 14-3-3 proteins bind to and sequester the transcriptional coregulators YAP/TAZ to the cytoplasm, inhibiting their function.
An anticancer drug is coupled to an antibody that targets a specific tumor antigen (or protein) that, ideally, is only found in or on tumor cells. The biochemical reaction that occurs upon attaching triggers a signal in the tumor cell, which then absorbs, or internalizes, the antibody together with the linked cytotoxin. After the ADC is internalized, the cytotoxin kills the cancer. Their targeting ability was believed to limit side effects for cancer patients and to give a wider therapeutic window than other chemotherapeutic agents, although this promise hasn't yet been realized in the clinic. ADC technologies have been featured in many publications, including scientific journals.
Activated carbon, in 50% w/w combination with celite, is used as stationary phase in low-pressure chromatographic separation of carbohydrates (mono-, di-, tri-saccharides) using ethanol solutions (5–50%) as mobile phase in analytical or preparative protocols. Activated carbon is useful for extracting the direct oral anticoagulants (DOACs) such as dabigatran, apixaban, rivaroxaban and edoxaban from blood plasma samples. For this purpose it has been made into "minitablets", each containing 5 mg activated carbon for treating 1ml samples of DOAC. Since this activated carbon has no effect on blood clotting factors, heparin or most other anticoagulants this allows a plasma sample to be analyzed for abnormalities otherwise affected by the DOACs. Carbon adsorption has numerous applications in removing pollutants from air or water streams both in the field and in industrial processes such as:
Sources: en.wikipedia.org
When measured by fatalities per person transported, however, buses are the safest form of transportation. The number of air travel fatalities per person are surpassed only by bicycles and motorcycles. This statistic is used by the insurance industry when calculating insurance rates for air travel. For every billion kilometers traveled, trains have a fatality rate that is 12 times higher than that of air travel, and the fatality rate for automobiles is 62 times greater than for air travel. By contrast, for every billion journeys taken, buses are the safest form of transportation; using this measure, air travel is three times more dangerous than car transportation, and almost 30 times more dangerous than travelling by bus. A 2007 study by Popular Mechanics magazine found that passengers sitting at the back of an aeroplane are 40% more likely to survive a crash than those sitting at the front. The article quotes Boeing, the FAA, and a website on aircraft safety, all of which claim that there is no "safest" seat. The study examined 20 crashes, not taking into account the developments in safety after those accidents. However, a flight data recorder is usually mounted in the aircraft's empennage (tail section) where it is more likely to survive a severe crash. Between 1983 and 2000, the survival rate for people in U.S. plane crashes was greater than 95 percent.
Mike Evans tied the record for consecutive seasons with at least 1,000 receiving yards, with 11. He shares this record with Jerry Rice. Evans also extended his own record of most such seasons to start his career. Aaron Rodgers became the fifth player to have 500 passing touchdowns. Trey McBride set the record for most receptions by a tight end in his first three seasons, with 221. The previous record of 216 was held by George Kittle. The Buffalo Bills became the first team to score at least 30 rushing touchdowns and at least 30 passing touchdowns in a season. Wild Card Round
Radiation therapy is usually reserved for people who have tumours remaining after surgery. These people often also receive medication to lower GH levels. Radiation therapy is given in divided doses over four to six weeks. This treatment lowers GH levels by about 50 percent over 2 to 5 years. People monitored for more than 5 years show significant further improvement. Radiation therapy causes a gradual loss of production of other pituitary hormones with time. Loss of vision and brain injury, which have been reported, are very rare complications of radiation treatments.
5-Oxo-eicosatetraenoic acid (i.e. 5-oxo-6E,8Z,11Z,14Z-eicosatetraenoic acid; also termed 5-oxo-ETE and 5-oxoETE) is a nonclassic eicosanoid metabolite of arachidonic acid and the most potent naturally occurring member of the 5-HETE family of cell signaling agents. Like other cell signaling agents, 5-oxo-ETE is made by a cell and then feeds back to stimulate its parent cell (see Autocrine signaling) and/or exits this cell to stimulate nearby cells (see Paracrine signaling). 5-Oxo-ETE can stimulate various cell types particularly human leukocytes but possesses its highest potency and power in stimulating the human eosinophil type of leukocyte. It is therefore suggested to be formed during and to be an important contributor to the formation and progression of eosinophil-based allergic reactions; it is also suggested that 5-oxo-ETE contributes to the development of inflammation, cancer cell growth, and other pathological and physiological events.
Sources: en.wikipedia.org
Peptides are very useful as therapeutic and diagnostic substances. Their use is getting more popular, and display systems offer a useful way to engineer peptides and optimise their binding capabilities. Cells express surface proteins which can be involved in a whole host of responses including recognition of other cells, interaction with other cells, and cell signalling. Many types of bacteria have cell surface proteins such as the enteropathogenic E. coli intimin protein which is involved in binding to host cells, or the OmpA protein of E. coli cells which is important in keeping the structure of the outer membrane. Many surface proteins are involved in bacterial cell attachment and invasion of the host cell. By using bacterial display, target proteins on the host cell can be identified. These surface proteins need to first be translocated across the bacterial cell membranes from the cytoplasm to the cell surface. Gram-negative bacteria have an additional periplasmic space, which Gram-positive bacteria lack, so they have a harder task of translocating proteins. The display of heterologous proteins on the bacterial cell surface normally requires the fusion of the protein with a surface protein, called a scaffold.
ADAMTS7 was identified as a protease that binds and cleaves COMP in a yeast two-hybrid screen using the epidermal growth factor (EGF) domain of COMP as the bait. However, this initial finding has been contested; a 2025 study demonstrated that purified ADAMTS7 does not exhibit proteolytic cleavage activity toward purified COMP. Furthermore, three independent unbiased N-terminal amine isotopic labeling of substrates (N-TAILS) proteomic studies identified a number of candidate substrates for ADAMTS7 but did not identify COMP as a potential substrate. Consequently, there is as yet no scientific consensus on the physiological function of ADAMTS7. Tissue inhibitor of metalloproteinases 4 (TIMP-4) appears to be the physiological inhibitor of ADAMTS7.
The charged aerosol detector (CAD) is a detector used in conjunction with high-performance liquid chromatography (HPLC) and ultra high-performance liquid chromatography (UHPLC) to measure the amount of chemicals in a sample by creating charged aerosol particles which are detected using an electrometer. It is commonly used for the analysis of compounds that cannot be detected using traditional UV/Vis approaches due to their lack of a chromophore. The CAD can measure all non-volatile and many semi-volatile analytes including, but not limited to, antibiotics, excipients, ions, lipids, natural products, biofuels, sugars and surfactants. The CAD, like other aerosol detectors (e.g., evaporative light scattering detectors (ELSD) and condensation nucleation light scattering detectors (CNLSD)), falls under the category of destructive general-purpose detectors (see Chromatography detectors).
Sources: en.wikipedia.org
Primary drying removes ice by sublimation at low pressure and low shelf temperature. Secondary drying removes bound water by raising the shelf temperature, often under the same vacuum. The two stages differ in the water state being removed.
Freezing determines ice crystal size, pore structure, and the concentration of solutes in remaining liquid. Faster freezing generally creates smaller ice crystals and a denser dried matrix. These features affect drying rate and reconstitution behavior.
Lyophilization reduces water content but usually leaves a small amount of water in the dried material. Some water remains bound to solids or trapped in the dried matrix. Very low water targets can require extended secondary drying, which may alter product stability.
Lyophilization relies on sublimation, so water moves from solid ice to vapor without becoming liquid. The material is frozen, pressure is reduced, and controlled heat is supplied. Vapor is captured on a cold condenser, leaving a dry porous solid.